Water leak detection in Tampa for commercial and multifamily buildings
Managed leak detection, 24/7 monitoring and automatic shutoff for condos, high-rises and commercial buildings across the Tampa Bay area.
- 150,000+
- active smart devices in the field
- $2.26M
- in water costs saved in 2025
- 24/7
- monitoring center
Why Tampa buildings carry water risk
A large share of Tampa Bay's waterfront condo stock dates to the 1970s and 1980s, and in many of those towers the supply lines, valves and fittings behind the drywall are the originals. Polybutylene-era supply piping from that period is a known failure risk that insurers scrutinize at renewal. When a fitting lets go on an upper floor, the water runs down through every unit below it.
The newer stock carries different risk, not less. Tampa has added a wave of new multifamily towers, and new plumbing fails too. Push-fit fittings, HVAC condensate lines and appliance connections are usually the first to let go, often within the first few years of occupancy. The water here runs hard, drawn largely from the region's limestone aquifers, and hard water scales valve seats, water heater elements and fixture supplies.
Then the climate decides how expensive a leak gets. A slow leak that would dry out in a northern building stays wet in Tampa's humidity, so the remediation, not the plumbing repair, is often what makes the claim large. Eddy runs its US operations out of Florida, so Tampa Bay buildings work with a team in-state, and the 24/7 monitoring center handles confirmation, escalation and shutoff around the clock.
Where leaks start in Tampa buildings
Original supply lines in 1970s and 80s towers
Waterfront condos from the boom decades still run their original supply lines, valves and fittings, including polybutylene-era piping that insurers scrutinize. Those failures start slowly, behind drywall, and the first sign is usually a stain two floors down.
Hard water scales valves and fixtures
The region's hard water builds scale on valve seats, heater elements and fixture supplies, so a valve that held for years can start to seep. Flow monitoring catches the drift before the failure.
HVAC running year round
Air handlers run nearly every day of the year, so condensate pans, drain lines and connections see far more hours than they would in a northern building. Continuous monitoring catches the drips those extra hours produce.
Units that sit empty for months
Many Gulf-coast condo units are seasonal homes. An empty unit is where a supply-line leak runs longest, because nobody is there to hear it. Monitoring and automatic shutoff do the job the absent owner cannot.
Smart leak detection in Tampa
A smart water leak detection system pairs wireless sensors and smart meters with automatic shutoff, so a Tampa building catches a leak in seconds instead of discovering it from a ceiling stain. Eddy runs the full stack as one managed program with a staffed 24/7 monitoring center on the chain.
Sensors plus flow intelligence
3-in-1 wireless sensors watch high-risk spaces for water, temperature and humidity while smart meters flag abnormal flow against thresholds learned from the building's own baseline.
No building Wi-Fi needed
Devices run on Eddy's own LoRaWAN network at 915 MHz, a long-range radio that holds a signal through concrete. Gateways backhaul over Ethernet or LTE cellular, and with cellular backhaul monitoring stays up even if building internet goes down.
Shutoff plus a live response
Automatic valves close the moment a configured rule fires, and Eddy's monitoring center calls the building's contacts within minutes of every alert. Every confirmed event closes with a Leak Incident Report.
See how the Eddy system works, from sensor placement to the monitoring center.
Coverage map
How Eddy works in a Tampa building.
Tampa Bay's 1970s and 80s towers still run their original supply lines, hard water scales valve seats and air handlers run nearly every day of the year. Turn the building to see where sensors, meters and valves sit, then run a leak through the system, from the first drop to the monitoring center's response.
Occupied building · Business hours
Drag to turn the building. Select a label, or run a leak through the system.
The system
Detect, control and respond, in one managed program.
Sensors sit where leaks start and meters watch the flow. Valves close on the rules you set, and a 24/7 monitoring center follows each alert until your team has eyes on it.
3 layers and 16 close-ups in this building
Detect
Two ways to find a leak before it finds a unit.
Sensors sit where leaks start, and meters watch the flow for the leaks no sensor can reach.
8 close-ups · select one to zoom in
Point-of-leak
Flow-based
Control
Valves that close the water before it closes the unit.
Valves close on the rules you set, automatically on a threshold or remotely from the dashboard.
4 close-ups · select one to zoom in
Respond
A live monitoring center that closes the loop.
Alerts go through Eddy's cloud to a 24/7 monitoring center, and an operator calls your team until someone has eyes on the water.
4 close-ups · select one to zoom in
What happens in a leak, step by step
- A washing machine supply hose bursts in a suite upstairs.
- Eddy H2O under the washer detects water and sends the alert over LoRaWAN.
- The building's gateway relays it. Your team and the 24/7 monitoring center are alerted at the same time.
- A shutoff rule closes the suite's Eddy IQ valve. The water stops at the source.
- An operator confirms the alert and calls your on-site team through the escalation protocol.
Automatic shutoff is configured per building. Some sites use operator-coordinated isolation instead.
Smart sensors at every leak point
Eddy places point-of-leak sensors and smart flow meters where water damage actually starts in Tampa buildings, from the mechanical room to a laundry hose, so a leak is caught at the source and shut off before it spreads.
Mechanical rooms
Boilers, water heaters and main risers, where a single failure floods fast.
HVAC and fan coils
Heat exchangers and condensate lines that drip behind walls and ceilings.
Kitchens
Supply lines, shutoffs and appliance connections under and behind the sink.
Bathrooms
Toilets, vanities and concealed in-wall fixtures on every floor.
Laundry
Washer hoses and laundry connections, a top source of overnight leaks.
Every minute changes the bill.
A leak gets bigger the longer it runs. Eddy detects in seconds and the monitoring center escalates within minutes, so the same failure is contained around minute two. Unmonitored, an after-hours leak runs six to eight hours before anyone arrives.
The leak starts at minute zero. Eddy contains it around minute two. Unmonitored, the same leak runs six to eight hours before staff arrive, and that red stretch is the avoided claim.
Build your system
Design your building's leak protection.
Two minutes of quick questions gets your building the right protection, previewed instantly.
- Sized to your asset class and budget
- Modular. Adjust anything before pricing
- An Eddy team member calls soon after you submit
Sensors, meters and shutoff, backed by a 24/7 monitoring center.
What stage is the project at?
Pick one to start. We tune every question and the system around it.
New constructionFrom breaking ground to substantial completion.
Existing buildingInstalled in existing buildings with minimal disruption to residents and operations.About two minutes.
Milestone inspections and reserve studies in Florida
Florida requires milestone structural inspections for older condo buildings three stories and taller, along with structural integrity reserve studies. A large share of Tampa Bay's stock dates to the 1970s and 1980s, so much of it has already crossed the age threshold and more boards are funding reserves under pressure. Documented water monitoring does not fund a reserve. What it shows a board, an engineer and an insurer is that the building's water systems are actively managed, not deferred.
A team behind every alert
A 3 a.m. alert is one chime. Nobody is awake to hear it.
Fast response is not just the hardware. The technology sees the water in seconds, and the managed service behind it, a monitoring center that calls your team within minutes, turns that into a contained event before it becomes a claim.
Tuned by real events
Built over a decade in operating buildings.
Eddy has been inside buildings since 2014. Sensor placement, alert thresholds and the monitoring-center playbook are tuned by what real water events across our monitored properties keep teaching us.
Built for the building
Sized to how the water system behaves.
Multi-family stacks, commercial towers, hospitality suites, course-of-construction projects. Each water system has its own failure pattern. The coverage map, response chain and shutoff sequence are scoped to the property in front of us, not a template.
Detect, contain, document
Every event leads to a closed incident.
Sensors find where water escaped. Automatic shutoff isolates the affected zone. The 24/7 monitoring center calls your team within minutes and stays on it until it's closed, with a Leak Incident Report on file.
Eddy's US operations are based in Florida
Eddy runs its US operations out of Florida, so Tampa Bay buildings work with a team in-state. Escalation stays with the 24/7 monitoring center, which confirms every alert, calls the building's contacts through the escalation protocol within minutes of the SMS, email and app alerts and can close a valve remotely when the building's response plan calls for it. Across Florida, Eddy protects coastal condo towers, commercial offices and hospitality properties the same way, from a single building to a multi-property portfolio.
Eddy at work in buildings like yours
Multi-family
A fan coil failed in an empty suite. The line was isolated before anyone set foot inside.
Ottawa, Ontario
A failing fan coil pulled abnormal make-up water through the heating and cooling loop in an unoccupied suite. Eddy detected the abnormal flow, the affected line was isolated remotely before prolonged loss, and a plumber completed the repair.
- Facility operator
- Property manager
- Asset owner
Construction
A leak at 4 AM on an empty job site. Eddy caught it anyway.
Fort Lauderdale, Florida
During active construction on a luxury development, a laundry connection began leaking in the early morning hours with the site empty. Eddy detected the moisture within seconds, the Monitoring Center prompted the on-site team, and the leak was contained before it could affect ongoing work.
- Builder or GC
- Risk manager
- Facility operator
Multi-family
A slow drip the eye could never catch. Smart metering saw it anyway.
Vancouver, British Columbia
A minor leak on a closed-loop cooling system showed up as continuous low flow on the make-up line, with nothing to see or hear. Eddy's smart metering flagged the abnormal pattern off-hours, and the superintendent isolated the chiller-room leak before it grew into a mechanical event.
- Facility operator
- Property manager
- Asset owner
Solutions for every building
Eddy protects every asset type the same way, with monitoring and shutoff tuned to how each building's water system behaves.
Multifamily and condos
Protect every suite and riser across high-rise and mid-rise residential.
Commercial
Keep Class A offices and mixed-use towers dry, floor by floor.
Construction
Cover active sites where water damage is a leading cause of loss.
Hospitality
Guard guest floors and back-of-house without disrupting the stay.
Institutional
Safeguard campuses, hospitals and labs where contents are irreplaceable.
Industrial
Watch process water and facility systems around the clock.
Tampa water leak detection FAQ
Do you serve Tampa, St. Petersburg and Clearwater?
Yes. Eddy's US operations are based in Florida and we protect commercial and multifamily buildings across the Tampa Bay area, including Hillsborough, Pinellas, Pasco and Manatee counties.
Can Eddy protect a unit while the owner is away for the season?
Yes, and that is where monitoring earns the most. Point-of-leak sensors and flow monitoring watch the unit whether anyone is home or not, and water can shut off automatically or on a remote command. The monitoring center escalates to the property manager and the building's contact list, not to an owner who is a thousand miles north.
Does hard water affect shutoff valves?
Scale is a wear factor on any mechanical valve in hard water, which is one reason a building should not assume an old manual valve will close when it is needed. Eddy pairs monitoring with its own automatic shutoff, so the response does not depend on a decades-old manual valve seating cleanly.
Will monitoring help our insurance in Florida?
Eddy's technology is approved by most insurers across North America to provide deductible or premium savings. Programs have documented premium savings of up to 20%, and deductible reductions of up to 80% have been documented at individual properties. Florida is a hard property market, so treat any figure as the start of a conversation with your broker. For specific questions about a Tampa Bay property, reach out to sghanbarian@eddysolutions.com.
Does Eddy cover new construction in Tampa Bay?
Yes. Water damage is a leading cause of builders risk loss, and the same program covers the site through construction, then converts to the operational system at handover without a second install.
How Eddy works
What is Eddy Solutions?
Eddy Solutions is managed water leak detection for builders, commercial asset managers and property managers, hospitals, hotels and conference centers, data centers and multifamily residential buildings across the Tampa Bay area. It combines point-of-leak and flow sensors, automatic shutoff, building wireless connectivity, a 24/7 monitoring center and insurance-grade reporting into one program from one vendor, so a leak is detected, contained, escalated and documented without your team running the response.
Eddy monitors 150,000+ active devices across North America and has prevented an estimated $98M (USD) in property damage last year alone. Aon's independent study found Eddy would have positively affected 58% of water-loss claims in commercial real estate.
How do we choose a commercial water leak detection company in the Tampa Bay area?
Look for five things. Sensors where leaks start, not only a meter on the main. Shutoff valves that close on their own when water runs. A staffed monitoring center that calls your team instead of only sending an app alert. Wireless coverage that holds a signal through concrete to mechanical rooms and parking levels. And a documented record of every event that your insurer can read.
Eddy covers all five for buildings across the Tampa Bay area, from a single tower to a full portfolio, with 150,000+ active devices in the field.
What happens after hours?
The 24/7 monitoring center is the after-hours response. Trained operators confirm every alert, escalate per the building's contact list, support the on-call contact, and stay on the line until the water is off and the response is verified.
Will this affect our insurance?
Yes. Eddy Solutions' technology is approved by most insurers across North America to provide deductible or premium savings. Given differences in asset types and building risk profiles, insurance incentives are not uniform. For specific insurance questions related to your property in the Tampa Bay area, please reach out directly to sghanbarian@eddysolutions.com.
How is the system sized for a building, and what does it cost?
Eddy's team walks the building, or reviews the construction drawings, and produces a tiered design matched to the asset class, water systems and insurance program. Our first step is an exploratory call with the relevant stakeholders to understand the problem you are looking to solve. Proposals come from our technical team in 7 days or less.
You can also get started immediately with our Build Your System tool at eddysolutions.com/build-your-system.
Do we have to open walls to install Eddy?
No. Sensor installs need no drywall cuts. Wireless sensors sit where leaks start, at fixtures, appliances, fan coils and the foot of each riser, and Eddy provisions and configures the meters and valves on the lines that need them.
What is smart water leak detection?
Smart water leak detection uses connected sensors and flow meters to watch a building's plumbing in real time, instead of waiting for someone to find a leak. Point-of-leak sensors catch water at the source and smart flow meters spot an abnormal run or a burst riser, and the system can shut the water off automatically or on a remote command. With Eddy, a 24/7 monitoring center acts on every alert, so detection turns into a response, not just a notification.
How is commercial water leak detection different from a home leak detector?
A home leak detector is usually a single sensor that pings an app. Commercial and multifamily leak detection has to cover dozens of risers, suites and mechanical rooms, hold a signal through concrete and steel and produce the documented response insurers expect. Eddy is built for that scale, with building-grade LoRaWAN wireless, point-of-leak and flow coverage across the property, automatic shutoff up to building mains and a managed 24/7 monitoring center.
What is the difference between leak detection and water leak protection?
Leak detection finds the water. Water leak protection stops the loss. Detection on its own is an alert that still needs someone to act on it. Eddy pairs detection with automatic shutoff and a 24/7 monitoring center that escalates the alert and closes the water, so the building is protected, not just alerted.
Does Eddy work for both multifamily and commercial buildings?
Yes. Eddy protects multifamily and condo towers, Class A offices and mixed-use buildings, hospitality, institutional and industrial properties and active construction sites. The same managed program tunes the sensor density, shutoff strategy and reporting to how each building's water system behaves. See the full product suite at eddysolutions.com/products.